Buying a distribution board or low-voltage switchboard requires more information than a breaker count and enclosure size. A useful supplier quotation identifies the intended assembly, electrical duty, incoming and outgoing circuits, installation conditions, approved component requirements and documentation. This guide helps Singapore industrial buyers prepare a clearer distribution board RFQ; it is not an electrical design, testing certificate or permission to substitute equipment.
1. Confirm the type of low-voltage assembly
Start with the approved single-line diagram (SLD) and the project specification. IEC 61439-1:2020 sets general requirements for low-voltage assemblies, used together with the applicable assembly-specific part. IEC 61439-2:2020 addresses power switchgear and controlgear assemblies. IEC 61439-3:2024 addresses distribution boards intended for operation by ordinary persons (DBO), within that part’s scope. Do not assume that every item called a “distribution board” falls under the same part. The appointed engineer, project requirements and assembly manufacturer must establish the correct application.
Singapore installations also require attention to applicable national rules, including SS 638, identified by the Energy Market Authority (EMA). EMA advises that applicable electrical works be performed or supervised by an appropriately Licensed Electrical Worker (LEW). Sourcing a panel is not the same as approving its electrical design or installation.
2. Distribution board BOQ: information needed for a comparable quotation
| RFQ field | What the buyer should provide or ask the supplier to confirm |
|---|---|
| Project and application | Site, intended duty (distribution, motor control or another approved function), new installation or replacement, indoor/outdoor location and applicable project specification. |
| Electrical system | Design-approved nominal voltage, frequency, number of phases, earthing arrangement and supply characteristics; never infer these from the enclosure photograph. |
| Incoming feeder | Incomer type, maker/series if specified, device rating, trip-unit requirements, accessories and approved coordination or setting schedule. |
| Outgoing circuits | SLD or circuit schedule identifying each feeder, protective-device type and ratings, spare ways and any required control or metering functions. |
| Assembly ratings | Assembly rated current, applicable short-circuit withstand or conditional ratings, and required design-verification evidence for the proposed configuration. These are not automatically equivalent to an individual circuit breaker’s interrupting ratings. |
| Busbars and connections | Approved busbar arrangement, neutral and protective-earth provisions, termination requirements, cable quantity/size and entry positions. Ask for evidence of assembly suitability and clearances. |
| Enclosure and environment | Approximate space envelope, mounting, environmental exposure, approved ingress/impact protection requirements where relevant, ventilation and service access. |
| Internal separation | Required form of internal separation and accessibility/maintenance conditions, if specified by the project; do not add a form or claim compatibility without the designer’s agreement. |
| Protection and controls | Design-specified MCB, MCCB, RCD/RCBO, SPD, isolator, metering and monitoring devices; exact manufacturer part numbers where substitution is restricted. |
| Delivery and documents | Required drawings, certificates or test/verification records, operating instructions, delivery destination, packing requirements and requested lead-time quotation. |
The table is a procurement intake checklist, not a universal assembly specification. Only the designer or properly authorised electrical professional should approve ratings, circuit protection and modifications.
3. Distinguish a device rating from an assembly rating
An MCCB may have an individual breaking-capacity designation such as Icu or Ics at a stated voltage, but that alone does not establish the completed board’s short-circuit performance. Ask the panel builder for the assembly’s applicable declared ratings and verification information under the selected IEC 61439 part. Protection selectivity, settings and any changes from a verified design must be reviewed by the responsible engineer and assembly manufacturer. For component-level intake, see our MCCB replacement RFQ guide.
4. Verification documents to request from the panel builder
- Approved or proposed SLD, general-arrangement drawings and circuit/component schedules clearly identifying revisions.
- The declared assembly standard and manufacturer identity, with documented assembly ratings for the offered configuration.
- Design-verification evidence appropriate to the applicable IEC 61439 requirements and proposed construction.
- Routine-verification records for the completed assembly, where required in the order and relevant standard.
- Traceable manufacturer references, data sheets and a list of any proposed deviations from the approved BOQ.
- Installation, operation and maintenance information, labels, terminal/connection details and the project’s requested commissioning handover documents.
IEC 61439 distinguishes design verification from routine verification. A product brochure or standalone breaker data sheet is not, by itself, evidence that a complete panel arrangement has been verified. Schneider Electric’s manufacturer guidance on IEC 61439 explains the different responsibilities of the original manufacturer and the assembly builder.
5. Replacement panels and OEM alternatives: avoid silent substitutions
If replacing an existing board, provide clear photographs of the nameplate and internal identification (taken only when safe and authorised), the original drawings, physical dimensions, feeder schedule and any restrictions on downtime or changes. Ask suppliers to distinguish an exact specified product from an alternative offered for engineering review. An apparent mechanical fit, familiar manufacturer logo or same current rating does not establish electrical interchangeability. Request proposed deviations in writing and obtain approval before purchase or installation.
6. Example wording for a Singapore distribution board RFQ
“Please quote the distribution board/low-voltage assembly described in the attached approved SLD, circuit schedule and project specification. Identify the applicable IEC 61439 assembly standard and provide your proposed drawings, exact component references, declared assembly ratings, design-verification basis and required routine-verification documentation. List deviations or substitutions separately for approval. State delivery terms, manufacturing lead time and documents provided. Do not assume alternative ratings, parts or a change to the protection design.”
Attach the latest drawing revision and a BOQ with quantities. If the approved specifications are incomplete, list the missing decisions as engineering clarifications rather than asking the vendor to assume values.
7. Send a better electrical sourcing enquiry
Grenglo Energy Pte Ltd is a Singapore-based industrial electrical supply and project sourcing partner supporting specified requirements in Singapore and selected Southeast Asian markets. For specification-led procurement support, review Grenglo’s power distribution and control components and industrial electrical replacement spares. You can request a quotation with the manufacturer references, approved drawings and material schedule. Product availability, suitability, documentation, pricing and delivery conditions must be confirmed against each enquiry; no OEM authorisation or interchangeable-product approval is implied.
Technical references checked 14 October 2026: IEC 61439-1:2020; IEC 61439-2:2020; IEC 61439-3:2024; EMA standards guidance; EMA Licensed Electrical Workers guidance. Check project-specific and locally adopted editions with the responsible professional; this article is not a certification statement.



